HOW TO: Remove and Replace Your Grip

Home Forums Technical FAQ HOW TO: Remove and Replace Your Grip

This topic contains 107 replies, has 54 contributors, and was last updated by gjarcher gjarcher 3 months, 4 weeks ago.

Viewing 15 posts - 1 through 15 (of 108 total)
  • Author
    Posts
  • February 25, 2006 at 11:21 pm #495034 Back to Top REPORT
    scottyluck
    Scottyluck

    Joined: 6/24/2004
    Many people have asked how to replace a grip. I recently purchased a new grip and decided to take some pics.
    The only tools you need are a hair dryer and a tube of 3M Weatherstrip Adhesive. I use the Black stuff.

    1) First secure the bow in a vise or a press if you have one. You could do it without either however it becomes a bit more awkward handling the bow.
    I put my bow in my RS Bow Vise.

    2) Next you need to heat up the grip and riser to soften the old adhesive. Use the hairdryer and apply heat directly to the back of the grip. This will heat the wood of the grip as well as the riser.
    Heat times will vary depending on the power of the hairdryer.
    It took me about 10 minutes to get the adhesive on my bow to soften.

    3) Once you get the grip and riser hot enough start putting pressure under the over hang at the bottom of the grip to try and lift the bottom of the grip off the riser.

    4) When the bottom starts to move keep pressure on it while pushing at the top of the grip. You may have to let the bottom fall back into place some in order for there to be room for the top of the grip to slide out. Once you get the top loose you will start to see a gap open between the grip cutout in the riser and the grip.
    *NOTE: Keep the pressure and movement focused toward the back of the grip and not side to side as this could crack the grip*

    5) keep working the grip back and forth, top to bottom, until it slides off.

    6)Once the grip is off there will be adhesive residue still on the riser. To remove it I took a small, flat blade screwdriver and carefully scarped it off. I also used a sharp utility knife blade to cut the thick stuff off.
    I tried to get the area where the new adhesive will go as clean as possible.
    *NOTE: BE CAREFUL!! Keep in mind that the riser is aluminum and you can cut into it with any sharp object. You can also very easily scrape the camo dip off. The object here is to get the majority of the old adhesive off the riser*
    The pic below is off my riser after I scraped the adhesive off.

    7) Once the riser is clean of the old adhesive apply a thin bead of the new 3M Weather strip adhesive to the riser in the area of the back of the grip. Use the old adhesive as guidance as to where to run the bead of the new adhesive.

    8) Next slide the new grip onto the riser.

    9) Finally, once the new grip is on, secure it with string, an elastic, packing tape or whatever you have available to keep pressure on the grip to the riser until the adhesive sets up.

    Pic of the 3M Weatherstrip adhesive for those of you that have never used it and don’t know what top look for. You should be able to purchase this from your local auto parts store for about $8.

    That’s it. Let it set up over night even though it probably won’t take that long.
    Take your time removing the old grip. If you apply much side to side pressure you stand a good chance of cracking the grip as one side os very thin.
    I would also recommend against using a screwdriver or some other tool to help pry the old grip off. This is another good way to crack or damage the grip. Heat is all you should need.

    Good luck!

    • This reply was modified 1 year, 3 months ago by vince71969 vince71969.
    February 25, 2006 at 11:36 pm #499710 Back to Top REPORT
    anton-the-viking
    Anton The Viking

    Joined: 11/23/2005
    I gave you an A+ for spelling and clarity of expression. Should definitely become a sticky with the current trend for grip modifications. Thanks, mate! :thumbup
    February 26, 2006 at 12:22 am #499711 Back to Top REPORT



    Joined: 5/24/2004
    That was an awesome explanation. I am in to middle of making my own grip for my legacy and I will use these tips. Thanks for the post!! =D/>” title=”Applause” /></div>


    </div><!-- .bbp-reply-content -->

</div><!-- #post-499711 -->

		
			
<div class=
    February 26, 2006 at 1:21 am #499712 Back to Top REPORT
    qdmbucks
    qdmbucks

    Joined: 1/7/2005
    that was an excellent picture narrative. Great work again.

    matt

    February 26, 2006 at 1:28 am #499713 Back to Top REPORT



    Joined: 5/24/2004
    very nice scotty =D/>” title=”Applause” />  <img src=
    February 26, 2006 at 1:51 am #499714 Back to Top REPORT
    gbbl-gbl
    GBBL GBL

    Joined: 11/26/2004
    Good Job Scotty…nice STS ;)
    February 26, 2006 at 1:57 am #499715 Back to Top REPORT
    bow4life
    bow4life


    Joined: 8/17/2004
    Awesome post, Scott. Very descriptive and the pics are great. :thumbup
    February 26, 2006 at 2:54 am #499716 Back to Top REPORT
    deer-repeller
    Deer Repeller

    Joined: 7/24/2004
    Can you say sticky?????
    February 26, 2006 at 3:12 am #499717 Back to Top REPORT
    micky
    Micky

    Joined: 10/11/2004
    Scott, thanks for an excellent post! I was discussing this with one of my brothers today. He is having a little torque problem with his new XT and I mentioned maybe shooting off the riser. Great timing! Thanks again.
    February 26, 2006 at 4:51 am #499718 Back to Top REPORT



    Joined: 5/24/2004
    :thumbup
    February 26, 2006 at 3:12 pm #499719 Back to Top REPORT



    Joined: 5/24/2004
    Great info. So when I took my bow in and had my pro shop fix a creek in my grip and got it back with pry marks on the riser by my grip…that was bad??? :cry:
    February 26, 2006 at 3:14 pm #499720 Back to Top REPORT
    scottyluck
    Scottyluck

    Joined: 6/24/2004

    Great info. So when I took my bow in and had my pro shop fix a creek in my grip and got it back with pry marks on the riser by my grip…that was bad??? :cry:[/quote:ld4g6v8u]
    Unnecessary is more like it.

    February 26, 2006 at 3:21 pm #499721 Back to Top REPORT
    slayer1
    slayer1

    Joined: 10/6/2005
    Excellent Post! What brand of grip is that Scott. Looks good! [=}=]
    February 26, 2006 at 3:24 pm #499722 Back to Top REPORT
    scottyluck
    Scottyluck

    Joined: 6/24/2004
    Excellent Post! What brand of grip is that Scott. Looks good! [=}=]

    It’s a custom grip made by Ron Hartl. He goes by the name “tronjo” over on ArcheryTalk. Go over there and do a search on his member name and you’ll see a number of different grips that he makes.

    February 26, 2006 at 5:30 pm #499723 Back to Top REPORT
    big-b
    Big B

    Joined: 1/23/2005
    very nice description. a+ :thumbup
Viewing 15 posts - 1 through 15 (of 108 total)