Can't tune my Chill

Home Forums Archery Tech Forum Can't tune my Chill

This topic contains 6 replies, has 4 contributors, and was last updated by bow-drawn Bow Drawn 1 year, 5 months ago.

Viewing 7 posts - 1 through 7 (of 7 total)
  • Author
    Posts
  • March 19, 2013 at 5:02 pm #569990 Back to Top REPORT

    GeneRagulsky

    Joined: 3/16/2007
    I have a 70lb Chill @ 29″. Easton fmj.   Started with 400s, then 340s and now 300s.
    Bad right tear thru paper.  To get rid of it, I have to drive my QUAD HDX all the way to the left.    Even with this I still have a small tear.  Big problem, I have to max out my Spott Hogg all the way to the left as well.  But I need to go even further.
    Been to 2 Mathews dealers and neither of them were very helpful.
    Oh ya, I have also tried 3 different QUAD rests, all with the same results.
    Any ideas???
    March 19, 2013 at 5:33 pm #569992 Back to Top REPORT
    danf
    DanF

    Joined: 1/23/2007
    View My Bows
    For starters, the 400 spine arrow is to weak. The 340 might be ok depending on how long they are cut. The 300 should be just right. I shoot a chill at 70 pounds and 30″ and I am shooting 300 FMJ’s that are cut to 29″ carbon to carbon. I am not having any issues with tuning whether it be field points or broadheads. The only thing that comes to mind would be maybe you are torquing the bow. I can’t be positive, but I think that might be one problem you could be facing. Hopefully somebody with a little more help will chime in!!! Good luck

    Sent from my iPhone using Tapatalk

    March 19, 2013 at 7:07 pm #570007 Back to Top REPORT
    99fatboy
    99fatboy

    Age: 52
    Joined: 2/15/2010
    Location: n.y.
    Photo Gallery
    i have seen some mr series bows that have had the lower cam at a bad angle,looking like this,/, not in line with the string. lay an arrow on the cams,they should both be close at the nocking point.
    black z7 magnum,tommy hogg,qad,b-stingers, vaportrail: blue smoke triumph,sword,hamskae,b-stingers:desert tactical chill R, tommy hogg,limbdriver pro v,ktech
    March 20, 2013 at 10:17 am #570116 Back to Top REPORT
    bow-drawn
    Bow Drawn

    Age: 63
    Joined: 11/14/2007
    Location: Ohio
    View My Bows

    i have seen some mr series bows that have had the lower cam at a bad angle,looking like this,/, not in line with the string. lay an arrow on the cams,they should both be close at the nocking point.

    If it is a cam lean issue what do you do about it?

    March 20, 2013 at 3:45 pm #570170 Back to Top REPORT
    99fatboy
    99fatboy

    Age: 52
    Joined: 2/15/2010
    Location: n.y.
    Photo Gallery
    it has been bearing misaligned in cam, bad limb set, or both. unfortunately ,very little can be done with the avs system to remedy lean, other than a small amount of twisting the loops inside themselves,but this does very little.
    black z7 magnum,tommy hogg,qad,b-stingers, vaportrail: blue smoke triumph,sword,hamskae,b-stingers:desert tactical chill R, tommy hogg,limbdriver pro v,ktech
    March 20, 2013 at 9:31 pm #570250 Back to Top REPORT

    GeneRagulsky

    Joined: 3/16/2007
    Well….   I actually took it back to a shop today.  The owner put me on the phone with a Mathew’s tech.  After my explaination of what was wrong and everything that I had attempted to fix it, the tech says they are sending me a complete new set of limbs.  Supposed to be here in 3 days.
    March 21, 2013 at 10:20 am #570316 Back to Top REPORT
    bow-drawn
    Bow Drawn

    Age: 63
    Joined: 11/14/2007
    Location: Ohio
    View My Bows
    That’s what I was going for when I asked what do you do for it or can you do anything with it before you rebuild the bow.
Viewing 7 posts - 1 through 7 (of 7 total)